Pirotecnia Posted June 20, 2012 Share Posted June 20, 2012 This is my homemade 2" spherical shell casing mould (lead). Hope you like it!Thanks! Link to comment Share on other sites More sharing options...
bob Posted June 20, 2012 Share Posted June 20, 2012 I use a pepsi ball cause it's cheap 2 bucks (of course you can get the lead for free so it does have that on it's side) but the pepsi ball is also none toxic and it's light that lead one must weigh a lot! IMOhow did you make the mould?it does look nicebob Link to comment Share on other sites More sharing options...
dan999ification Posted June 21, 2012 Share Posted June 21, 2012 nice work, i just got round to making my mould from givat's tutorial, its not strong enough [old plaster] but it will hold up enough to make a set of more durable ones from epoxy...or maybe lead. how much does it weigh? dan. Link to comment Share on other sites More sharing options...
Pirotecnia Posted June 22, 2012 Author Share Posted June 22, 2012 (edited) Hi, I've made some improvements on my mould, as you can see in the photos. I sank a little the cavity and i punched a hole in the bottom to get the paper casing off easier.Now, it works very good to me!Weigth about 900 gram. Thanks! Edited June 22, 2012 by Pirotecnia Link to comment Share on other sites More sharing options...
Col Posted July 25, 2012 Share Posted July 25, 2012 I bet that works very well. The weight of the female mold would compress the paper if you left it to dry upside down.. Link to comment Share on other sites More sharing options...
ivars21 Posted July 25, 2012 Share Posted July 25, 2012 Where do you get so much lead? Link to comment Share on other sites More sharing options...
bob Posted July 25, 2012 Share Posted July 25, 2012 you can buy pure lead or get tire weights it really is not that much bob Link to comment Share on other sites More sharing options...
WSM Posted July 30, 2012 Share Posted July 30, 2012 Hi,I've made some improvements on my mould, as you can see in the photos. I sank a little the cavity and i punched a hole in the bottom to get the paper casing off easier.Now, it works very good to me!Weigth about 900 gram.Thanks! If you want a better molten lead pour and have access to sodium metal, add a small piece of sodium to the molten lead, skim the dross and pour. The sodium is a "getter" for various things that goof up the lead and allow "holidays" in it. WSM 1 Link to comment Share on other sites More sharing options...
Pirotecnia Posted August 2, 2012 Author Share Posted August 2, 2012 Where do you get so much lead? I get the lead from old batteries Link to comment Share on other sites More sharing options...
dan999ification Posted September 3, 2012 Share Posted September 3, 2012 i made one this week and it works very well indeed, 3inch in a bean can, after messing about with a baloon and plaster i realised it was easier filling a hemi with lead putting it in a bean can pole up and cover with lead, my female mould is heavier than the male and drying is easy if you dont use too much glue, five minutes in the oven and stack them while still hot stops them deforming, after cutting the discs and petals i made ten hemis in under an hour, im so impressed with it, this is the way to go. Dan. Link to comment Share on other sites More sharing options...
psyco_1322 Posted September 4, 2012 Share Posted September 4, 2012 What the heck is a Pepsi ball? Can I drink it? Link to comment Share on other sites More sharing options...
bob Posted September 5, 2012 Share Posted September 5, 2012 (edited) LOL I wish it's a rubber type foam ball with red white and blue in lot's of sizes, I'd post a picture of it but almost all of the paint is worn off itbob Edited September 5, 2012 by bob Link to comment Share on other sites More sharing options...
Recommended Posts