Jump to content
APC Forum

Skylighter firefly formula?


FlaMtnBkr

Recommended Posts

Does anyone have the Skylighter firefly formula? I bought 5 lbs and it didn't come with the instructions. I have the aluminum and have heard it is a pretty good formula.

 

If you would rather pm me the details that would be fine.

 

Thanks

Edited by FlaMtnBkr
Link to comment
Share on other sites

http://www.skylighte...y-cut-stars.asp

 

It is based off of Shimizu Chrysanthemum 8 with 5% firefly aluminum added. I just got some firefly aluminum blend in a group buy and a few of us were discussing better results using SGRS instead of dextrin. We thought it was Mike Swisher who mentioned that first, but are not positive.

 

Edited by nater
Link to comment
Share on other sites

Thanks for the replies and tips. I did a quick search there but didn't find it. Guess I spelled something wrong. Thanks for pointing me in the right direction. I've had the aluminum for over a year and when I looked in the container there wasn't even the standard MSDS so the paperwork must have been overlooked.
Link to comment
Share on other sites

I rather doubt Mr. Swisher would recommend the use of SGRS in firefly stars. I've used it, and it works fine though. He probably recommended the use of wheat paste to bind the stars/comets instead of water.

 

Allrockets, is this something you've actually observed with firefly stars, or just speculation?

 

These stars were SGRS bound. The effect was given away a bit early because I didn't quite get all of the fines screened out. These were not made with the cut firefly Al that skylighter sells. Rather a graded version of coarse flitters.

 

Link to comment
Share on other sites

I rather doubt Mr. Swisher would recommend the use of SGRS in firefly stars. I've used it, and it works fine though. He probably recommended the use of wheat paste to bind the stars/comets instead of water.

 

Allrockets, is this something you've actually observed with firefly stars, or just speculation?

 

These stars were SGRS bound. The effect was given away a bit early because I didn't quite get all of the fines screened out. These were not made with the cut firefly Al that skylighter sells. Rather a graded version of coarse flitters.

 

 

SGRS is also Gene Y. and Steve J's binder of choice for FFOC and it works phenomenally well. Mike did tell me directly and Gene via email that White Pine was essential for good FF.

 

-dag

Link to comment
Share on other sites

SGRS is also Gene Y. and Steve J's binder of choice for FFOC and it works phenomenally well. Mike did tell me directly and Gene via email that White Pine was essential for good FF.

 

-dag

 

 

Is that something new Dave, the white pine? It's my understanding from Bill Kimbrough himself, that SYP (southern yellow pine) is the coal of choice for this particular effect. He's sent some to me a couple of times now to spare me buying boards at the lumber store. Then again, that's Bill's particular formula which may be different.

 

Can't say on the binder. I typically use dextrin but will try the SGRS one of these days.

 

 

DanB

Link to comment
Share on other sites

Dan, I'm sorry, spoke before I could check my notes.

My bad... There a few of us that struggled through the whole trial last year and the effect for the FFOC was only achieved with southern yellow pine.

 

-dag

Link to comment
Share on other sites

  • 1 month later...
just out of curiosity, what is firefly aluminum? i would assume that it's just a form in the sense that flakes, dust, and spherical are forms.
Link to comment
Share on other sites

It's a form of coarse flake. It was originally made with something that resembles something like large mesh bright flake Al that was graded to only include the coarse stuff. Now some people use something that looks more like chopped up aluminum foil. It's regular rectangles of aluminum, almost like glitter or little pieces of confetti.
Link to comment
Share on other sites

×
×
  • Create New...