Jump to content


Photo
- - - - -

My shells


  • Please log in to reply
48 replies to this topic

#41 fckiamdead

fckiamdead

    Pyromaniac

  • Donator
  • PipPipPip
  • 85 posts
  • Gender:Male

Posted 01 April 2018 - 06:58 AM

An attempt to make a cylinder shell whit timed reports. 3pc of timed rising effects. BP/FeTi "ring"

 


  • pyrokid likes this
Youtube channel:
------------------------------
https://www.youtube....sv10AA8-yqIbuAw
------------------------------

#42 dynomike1

dynomike1

    Firebreather

  • Donator - HE
  • PipPipPipPipPip
  • 1,192 posts
  • Gender:Male
  • Location:W. Tn.
  • Interests:Blowing Beaver dams, Shooting Cannons, Hunting, making fireworks.Buying guns.

Posted 01 April 2018 - 08:12 AM

I cant ever get my inserts to go off at the same time.


There are very few problems that cant be solved with explosives.
                             Explosives are a bang up job.

#43 fckiamdead

fckiamdead

    Pyromaniac

  • Donator
  • PipPipPip
  • 85 posts
  • Gender:Male

Posted 02 April 2018 - 09:24 AM

2inch peanut shell, Glitter.

 


Youtube channel:
------------------------------
https://www.youtube....sv10AA8-yqIbuAw
------------------------------

#44 fckiamdead

fckiamdead

    Pyromaniac

  • Donator
  • PipPipPip
  • 85 posts
  • Gender:Male

Posted 02 April 2018 - 09:28 AM

I cant ever get my inserts to go off at the same time.

I made a time fuse cutter, works great!


Youtube channel:
------------------------------
https://www.youtube....sv10AA8-yqIbuAw
------------------------------

#45 dynomike1

dynomike1

    Firebreather

  • Donator - HE
  • PipPipPipPipPip
  • 1,192 posts
  • Gender:Male
  • Location:W. Tn.
  • Interests:Blowing Beaver dams, Shooting Cannons, Hunting, making fireworks.Buying guns.

Posted 02 April 2018 - 05:33 PM

I have a fuse cutter and still cant get em to go off at the same time.


There are very few problems that cant be solved with explosives.
                             Explosives are a bang up job.

#46 MrB

MrB

    Firebreather

  • HE Qualified
  • PipPipPipPipPip
  • 1,748 posts
  • Gender:Male

Posted 02 April 2018 - 07:32 PM

I use a cutter, and have done both punched through timefuse, with a strand of BM in the hole, dipped i NC / BP slurry, and tied, bent over the end, BM. For me, no doubt the best results were with punched hole for the BM, followed by NC / BP slurry, and last... well.
It's just down to how consistent you can be, and that of course also applies to the timefuse. If it isn't consistent, then nothing else will be either.

#47 rocketmaster

rocketmaster

    Smelt the smoke

  • Full Member
  • Pip
  • 8 posts
  • Gender:Male
  • Location:Land Downunder

Posted 20 April 2018 - 05:50 PM

@fckiamdead what sort of machine are you using to roll your stars? Picture?



#48 fckiamdead

fckiamdead

    Pyromaniac

  • Donator
  • PipPipPip
  • 85 posts
  • Gender:Male

Posted 20 April 2018 - 11:37 PM

@fckiamdead what sort of machine are you using to roll your stars? Picture?

Hello

I can take some pictures tomorrow for you.

 

Regards 


Youtube channel:
------------------------------
https://www.youtube....sv10AA8-yqIbuAw
------------------------------

#49 fckiamdead

fckiamdead

    Pyromaniac

  • Donator
  • PipPipPip
  • 85 posts
  • Gender:Male

Posted 26 September 2018 - 05:01 AM

An attempt on making a red horsetail cylinder "smoke" shell

 

Yes there is a tail...but kind of small one.. the bang was nice though... you have to start somewhere...

 


Youtube channel:
------------------------------
https://www.youtube....sv10AA8-yqIbuAw
------------------------------




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users