skid68 Posted July 2, 2014 Share Posted July 2, 2014 This section needs more posts! Not quite a zipper as it wasn't fused that quick. But I did start it out slow and sped it up as it went along. All in all I'm real happy with it. Link to comment Share on other sites More sharing options...
kilnj69 Posted July 2, 2014 Share Posted July 2, 2014 Very nice cake, I too would like more competitions. Just for fun Link to comment Share on other sites More sharing options...
Zumber Posted July 2, 2014 Share Posted July 2, 2014 red colour was nice...!! Link to comment Share on other sites More sharing options...
skid68 Posted July 3, 2014 Author Share Posted July 3, 2014 Thanks guys. Cakes can be daunting. They are a lot of work for a short display. But they are fun. The red was called "Buell Red" Link to comment Share on other sites More sharing options...
asdercks Posted July 4, 2014 Share Posted July 4, 2014 Not bad for at all, I am sure you will get better timing/speed as you keep buiding more of these cakes, good job. Link to comment Share on other sites More sharing options...
modelrocket Posted November 11, 2014 Share Posted November 11, 2014 very nice Link to comment Share on other sites More sharing options...
PyroAce Posted December 28, 2014 Share Posted December 28, 2014 (edited) skid68 what formulas were you're stars, I loved them, looked like you had some Titanium in there too for the tail effect? Edited December 28, 2014 by PyroAce Link to comment Share on other sites More sharing options...
Pretty green flame Posted December 28, 2014 Share Posted December 28, 2014 Looks very nice. Link to comment Share on other sites More sharing options...
Arthur Posted December 28, 2014 Share Posted December 28, 2014 Great cake, I'd buy that if it was on sale here. I like the increasing pace as it burns. UK cakes seem to be slow with 30 seconds getting you 15 - 25 tubes so I like the faster cakes even just the pearls. Link to comment Share on other sites More sharing options...
skid68 Posted January 16, 2015 Author Share Posted January 16, 2015 (edited) Thanks guys. PyroAce. No titanium in them. I believe the tail you are seeing is the prime layer burning off.The red is Buell red, the purple is Veline Magenta. I think the green and yellow were go getter formulas. Edited January 16, 2015 by skid68 Link to comment Share on other sites More sharing options...
Mumbles Posted January 16, 2015 Share Posted January 16, 2015 The other possibility is that it's parlon or red gum. I've always noticed a slight tail like that if I didn't screen the compositions through a fine enough screen. This seems to remove some debris and granular material that leaves a slight tail. 60 mesh usually worked for me. The unwanted parlon tail shows up if the stars were bound with acetone instead of water generally as well. Link to comment Share on other sites More sharing options...
skid68 Posted January 16, 2015 Author Share Posted January 16, 2015 Mumbles. It's the Spanish Monocapa prime. The prime does contain Red Gum, but also contains 12% MgAl. Heck, it could even be the black Iron oxide in the prime eh? Link to comment Share on other sites More sharing options...
Mumbles Posted January 16, 2015 Share Posted January 16, 2015 I was speaking about the parlon and red gum in the stars themselves. The tail goes on longer than I'd expect to be coming from prime, but anything is possible. Link to comment Share on other sites More sharing options...
Bobosan Posted January 16, 2015 Share Posted January 16, 2015 Mumbles, believe it is caused by the monocapa prime. I noticed a tail when using a thick layer, probably MgAl caused. Link to comment Share on other sites More sharing options...
Recommended Posts