Maserface Posted January 6, 2016 Share Posted January 6, 2016 (edited) This is a gerb that I made, black powder based with additional coarse steel powder for sparks Type: Gerb Caliber: 1" ID Performance description: Black powder with coarse steel powder for sparks Formula: 100 parts screen mixed black powder, 15 parts steel powder. Additional Details: The composition was wet with 1% moisture (to reduce messy dust) and pressed into the tube at 3500PSI. Edited January 6, 2016 by Maserface 2 Link to comment Share on other sites More sharing options...
Sparx88 Posted January 6, 2016 Share Posted January 6, 2016 This is a gerb that I made, black powder based with additional coarse steel powder for sparks Sparks!, I like sparks. and thems some nice onesWhat kind of steel was it? Did you make it? comon man, pleeeease tell me, I got the sparx itch coming on! Link to comment Share on other sites More sharing options...
Maserface Posted January 6, 2016 Author Share Posted January 6, 2016 Its this stuff I got it on one of the sales for about 50% off, this was my first project with it, but I really like it! You might need a protective coating on the steel if you plan on storing finished devices for more than a few weeks. I shot mine within a few hours. 1 Link to comment Share on other sites More sharing options...
Sparx88 Posted January 7, 2016 Share Posted January 7, 2016 Right on, preciate that. This would look good for rockets which is what I'll do first when it arrives..: Link to comment Share on other sites More sharing options...
Stef727 Posted January 7, 2016 Share Posted January 7, 2016 (edited) Replace the steel powder with titanium sponge. You will be surprised at how good and bright it will be Edited January 7, 2016 by Stef727 Link to comment Share on other sites More sharing options...
michalsiegel Posted January 16, 2016 Share Posted January 16, 2016 Really nice gerb! What dou you say about my magnesium fountain? https://youtu.be/2XLXZajB2pA Link to comment Share on other sites More sharing options...
OldMarine Posted January 16, 2016 Share Posted January 16, 2016 I may have already posted this here but here's my first gerbs (BP and Ti) 3 lb x 6" 1 Link to comment Share on other sites More sharing options...
Maserface Posted January 17, 2016 Author Share Posted January 17, 2016 Nice! You guys should make your own respective threads, with more details (like the one we are in). It makes keeping up a lot easier Link to comment Share on other sites More sharing options...
memo Posted January 17, 2016 Share Posted January 17, 2016 maserface, you have me thinking now . I wonder if the metal fillings left behind by a cut off saw would work ? it is mostly fine metal with a little bit of cut off saw blade mixed in. I am going to give it a try hand ramming. I don't have a press. memo Link to comment Share on other sites More sharing options...
MrB Posted January 18, 2016 Share Posted January 18, 2016 I wonder if the metal fillings left behind by a cut off saw would work ? Probably depends on the sparks you want, and the teeth sizing on your saw, but it works, i use it all the time. I've also used turnings from lathe's, and mills. If your priority is pyro, and not production times, you can set up your cut and feed speeds so that the later two produces ready to use material. Doing it like this leaves you with a hot, clean product, without contamination from cutting fluids, since you haven't used any.If your just grabbing whats "left over" after metal working, more often then not it ends up being soaked in cutting fluids. I haven't bothered to actually wash it. I might rinse it of, just to get the worst of it out, it seams to speed up the drying process, and doesn't leave a sticky mess behind. But that might depend on your cutting fluid. We use water-soluble synthetics. Supposedly biodegradable, and "green", yet it has to be collected by a waste disposal service, and is treated as hazardous material. (Only the thrown out fluids, the metal goes straight to recycling, if i don't steal it)B! Link to comment Share on other sites More sharing options...
memo Posted January 18, 2016 Share Posted January 18, 2016 mr b this is a dry cut off saw. the only junk in the filing would be fiber from the disk and not much of that. memo Link to comment Share on other sites More sharing options...
MrB Posted January 18, 2016 Share Posted January 18, 2016 Those disc's pretty much set what ever they cut on fire, (possibly bad) and only produce dust. (possibly good) I'm not sure that's going to provide the kind of result your looking for. Try it, but it might turn out the iron dust is already "spent" so to speak.Then again, it might not.B! Link to comment Share on other sites More sharing options...
Elisey Posted September 16, 2019 Share Posted September 16, 2019 https://youtu.be/QdT4q9Ib4N0Gerb and wheel. Link to comment Share on other sites More sharing options...
Recommended Posts